RC LANDER THUNDER BLADE (Single 64mm)
ALMOST READY-TO-FLY PACKAGE
Material: EPO Foam
Wing span: 760mm
Fuselage Length: 890mm
AUW: Approx 850g
EDF (Lander Metal EDF): 64mm (4s) (included)
Motor: 3900KV Lander Inrunner Motor (included)
Power: 4S 2200mAH 25C or above (NOT included)
Thrust : up to 1050g (4S)
ESC : 65A Brushless ESC (included with T-Plug+3.5mm Conn)
Servos: 9g servos x 5 (included & installed)

Features:
This is a 4S setup with approx thrust up to 1050g. The Thunder Blade is a robust EDF Jet made of Super EPO foam that weighs less than 1kg to fly. It comes with basic piano-wire landing gear kit with wheels and can be launched by hand due to the high thrust efficiency of the 64mm Metal Fan. The package includes everything you need except Lipo which requires 4S 14.8V and all 5 Servos / 65A Brushless ESC / 64mm Metal EDF / Motor (3900KV) are included in the package. The system is tested and leaves you free from unnecessary guess work and power matching!

RC LANDER Lighting Kit Set
(PLUG N PLAY)- NORMAL Nav Lights
Complete lighting kit with pre-installed LEDs pre-wired and soldered! You do not need to solder as it is Plug N Play!

Consists of:
1) Landing Head Light x 1
3) Red Beacon LED x 1
3) Starboard LED x 1
4) Port LED x 1
5) Control Module (With 2 Port Dials for sense adjustment)
6) Balancer Adaptor for 3S
7) Balancer Adaptor for 4S
8) Throttle and ESC Connectors to RX included

RC LANDER Lighting Kit Set
(PLUG N PLAY)-WITH AFTERBURNER!
Complete after-burner lighting kit with pre-installed afterburner LEDs on ply-ring, All LEDs are pre-wired and soldered! You do not need to solder as it is Plug N Play!

Consists of:
1) Afterburner ring LEDs (Red)
2) Landing Head Light x 1
3) Red Beacon LED x 1
4) Starboard LED x 1
5) Port LED x 1
6) Control Module (With 2 Port Dials for sense adjustment)
7) Balancer Adaptor for 3S
8) Balancer Adaptor for 4S
9) Throttle and ESC Connectors to RX included

RC LANDER 70mm Vector Thrust System
Works with any jet with 70mm exhaust. These nozzles are a great way to add thrust vectoring to your jet, the nozzles will transform your jets capability and allow you to do many manouvres not possible with conventional controls. Fitted with foam exhaust ring and control horns ready to connect to servos and mix in with your elevator and rudder.

- ball link push horn (1.4mm) installed
- Wooden firewall mounting
- Upper/Lower ply for vector support
- Full set metal vector system assembled
- 2.6mm screws for fuse installation x 4
- Predrilled LED holes for afterburner lights

RC LANDER 90mm Vector Thrust System
Works with any jet with 90mm exhaust. These nozzles are a great way to add thrust vectoring to your jet, the nozzles will transform your jets capability and allow you to do many manouvres not possible with conventional controls. Fitted with foam exhaust ring and control horns ready to connect to servos and mix in with your elevator and rudder.

- ball link push horn (1.4mm) installed
- Wooden firewall mounting
- Upper/Lower ply for vector support
- Full set metal vector system assembled
- 2.6mm screws for fuse installation x 4
- Predrilled LED holes for afterburner lights

RC LANDER F16 Drop Tanks Set
This is the replacement drop tanks for RC Lander F-16s and F2Bs. You may also consider this for other similar models as an extra payload for your other EDF models. Suitable for 70mm models.
Comes in pack of 2 (1 pair)
Colour : Off White (Bluish Tint)