|
ITEM
|
Decription
|
Stock
|
comes with heat shrink
tubes |
HYPERION
HP-CONPRO35
Pin
Size : 3.5mm
Weight (1M/1F pair) : 3.32g
Hole Dia. : 3.0mm*
Max Wire Size : 5.0mm
Current : 80A/160A**
Heatshrink Tubes : Included
"Cheap" connectors always end up
costing a lot... Poor connections rob power -
and the money you spent on motor and batteries.
And they can lead to intermittent problems which
are hard to diagnose, not to mention crashes...
The new Hyperion "Pro" line of connectors has
these advantages:
• Superior Mechanical System to maintain
connector tension over many cycles
•
Large Contact Surfaces and high-quality real gold
plating for lowest resistance
•
Highest Current Handling on size/weight basis
•
Ribbed Rear Portion for excellent heat shrink
grip
* "Hole Dia" in most cases matches
wire gauges used on ESC and Motors with similar
current ratings. "Max. Wire Size" is for "Butt
Joint" soldering when needed with large wires
(center of wire is trimmed to Hole Size, and larger
diameter section remaining is soldered flush to
back of the connector).
** "Current" is given as CONTINUOUS vs. 30 Seconds.
These apply to Battery<>ESC connections or brushed
motors. Note that when the connectors are used
to connect a brushless MOTOR and ESC, and current
is measured at the BATTERY, these ratings can
be increased 33%. |
|
|
comes with heat shrink
tubes |
HYPERION
HP-CONPRO45
Pin
Size : 4.5mm
Weight (1M/1F pair) : 6.25g
Hole Dia. : 4.0mm*
Max Wire Size : 6.0mm
Current : 140A/280A**
Heatshrink
Tubes : Included
"Cheap" connectors always end up
costing a lot... Poor connections rob power -
and the money you spent on motor and batteries.
And they can lead to intermittent problems which
are hard to diagnose, not to mention crashes...
The new Hyperion "Pro" line of connectors has
these advantages:
• Superior Mechanical System to maintain
connector tension over many cycles
•
Large Contact Surfaces and high-quality real gold
plating for lowest resistance
•
Highest Current Handling on size/weight basis
•
Ribbed Rear Portion for excellent heat shrink
grip
* "Hole Dia" in most cases matches
wire gauges used on ESC and Motors with similar
current ratings. "Max. Wire Size" is for "Butt
Joint" soldering when needed with large wires
(center of wire is trimmed to Hole Size, and larger
diameter section remaining is soldered flush to
back of the connector).
** "Current" is given as CONTINUOUS vs. 30 Seconds.
These apply to Battery<>ESC connections or brushed
motors. Note that when the connectors are used
to connect a brushless MOTOR and ESC, and current
is measured at the BATTERY, these ratings can
be increased 33%. |
|
|
|
|
2.0mm
Gold Connectors
Pack
of 10 pairs
10 Male / 10 Female
Pack of 5 pairs
5 Male / 5 Female |
|
|
|
|
3.5mm
Gold Connectors
Pack
of 10 pairs
10 Male / 10 Female
Pack of 5 pairs
5 Male / 5 Female |
|
|
|
|
4.0mm
Gold Connectors
Pack
of 10 pairs
10 Male / 10 Female
Pack of 5 pairs
5 Male / 5 Female |
|
|
|
|
6.0mm
Gold Connectors
Pack
of 10 pairs
10 Male / 10 Female
Pack of 5 pairs
5 Male / 5 Female |
|
|
(Item
Code : DEAN-9022) |
DEANS
ULTRA Y-SERIES
for 2 Lipos
to 1 ESC
The
Dean's Y Series harness allows you to connect
two identical packs in series to effectively double
the available voltage of use. Use this to construct
a larger cell count pack out of two matching smaller
packs. (eg connecting 2 3S packs to make it 6S)
Wire : 14AWG High Stands Silicon Wire
Length : Each Side 50mm
Cautions and Warnings:
Only use with batteries and ESCs that follow the
standard polarity conventions for Deans connectors.
All batteries must be fully charged before connection.
Do not charge while connected. All batteries MUST
be identical same brand same "C" rating same mAh
rating |
|
|
(Item
Code : DEAN-9023) |
DEANS
ULTRA Y-PARALLEL
for 2 Lipos
to 1 ESC
The Dean's 2P
harness allows you to connect two identical packs
in parallel to effectively double the available
current and duration of use. Use this to construct
a larger capacity pack out of two matching smaller
packs.
Wire
: 14AWG High Stands Silicon Wire
Length : Each Side 50mm
Cautions and Warnings:
Only use with batteries and ESCs that follow the
standard polarity conventions for Deans connectors.
All batteries must be fully charged before connection.
Do not charge while connected. All batteries MUST
be identical same brand same "C" rating same mAh
rating
|
|
|
(Item
Code : DEAN-9025) |
DEANS
ULTRA Y-PARALLEL
for 1 Lipo
to 2 ESCs
The Dean's Y harness allows you to
connect two ESCs (Electronic Speed Controls or
Motor Controllers) to one battery pack. Use this
to run two separate power systems off of a single
pack.
Wire
: 14AWG High Stands Silicon Wire
Length : Each Side 50mm
Cautions and Warnings:
Only use with batteries
and ESCs that follow the standard polarity conventions
for Deans connectors. Do not Charge while Connected
|
|
|
|
|
Futaba
Style Servo Extension
Y-HARNESS, 15cm
With durable hard casing at Y-joint
Futaba Colour Code
|
|
|
|
|
Futaba
Style Servo Extension
Y-HARNESS, 30cm
With durable hard casing at Y-joint
Futaba Colour Code |
|
|
For ORION/TRAXPOWER
2 Cell Race Packs
Click above for full diagram
|
HP-EOSOUT-CAR02
EOS Output Harness for Balance Charging 2S Car
Packs such as ORION and TRAXPOWER
Fits EOS balance Chargers
(EOS0403i, 0606i-x, 0610i-x) and LBA10. Battery-side
has 4mm main bullet connectors, plus 2mm bullet
for balance port on battery. Because long wires
and extra connectors in the balance circuit can
potentially reduce accuracy of charging and balancing,
this harness in made to connect directly to the
Balance Port on Hyperion balance chargers.
However, if you prefer (or need the extra length)
you may use the Hyperion multi-adapter which came
with your EOS charger and plug the EOSOUT-CAR02
balance connector into the 6S port on the Hyperion
multi-adapter. If you have a charger which can
charge 3.7v LiPo batteries, but does not have
a balancer built in, you can use a Hyperion LBA10
Balancer between your charger and the EOSOUT-CAR02
harness, to balance charge your 2S Car pack. |
|
|
|
|
HYPERION
TX/RX CHARGE CABLES SET
FOR AIRTRONICS-SANWA-HITEC
Two Separate Charge harnesess for AIRTRONICS-SANWA-HITEC
Transmittter and Receiver Batteries 1Meter (39")
cable length, 4mm Bullet connectors to charger
attached. |
|
|
|
|
HYPERION
TX/RX CHARGE CABLES SET
FOR FUTABA
Two Separate Charge harnesess for FUTABA Transmittter
and Receiver Batteries 1Meter (39") cable length,
4mm Bullet connectors to charger attached. |
|
|
|
|
HYPERION
TX/RX CHARGE CABLES SET
FOR JR / SPEKTRUM
Two Separate Charge harnesess for JR Transmittter
and Receiver Batteries 1Meter (39") cable length,
4mm Bullet connectors to charger attached. |
|
|
Back
to ACCESSORIES MAIN PAGE 
|
|
|
|
|
