|
ITEM
|
Description
|
Price
|
|
|
REVOX
G2213/20
No. Of cells : 3 Li-Poly
RPM/V : 1000 KV
Operating Current: 6A ~ 15A
Peak Current: 19A (15 secs)
Suggested prop: 10x4.7, 10x6, 10x7 or 11x5.5E
Lipo Battery: 1300~2200mAh 3S1P
Weight: 59g
Dimensions: 27.6 x 32mm
Shaft Size: 3.175mm
Recommended for models between 400-600g |
|
|
|
|
REVOX
G2213/22
No. Of cells : 3 Li-Poly
RPM/V : 910 KV
Operating Current: 6A ~ 14A
Peak Current: 17A (15 secs)
Suggested prop: 10x4.7,
10x6, 10x7 or 11x5.5E
Lipo
Battery: 1300~2200mAh 3S1P
Weight: 59g
Dimensions: 27.6 x 32mm
Shaft Size: 3.175mm
Recommended
for models between 400-600g
|
|
|
|
|
REVOX
G2217/16
No. Of cells : 3 Li-Poly
RPM/V : 1000KV
Operating Current: 6A ~ 18A
Peak Current: 18A (15 secs)
Suggested prop: 10x4.7, 10x6.0, 11x4.7
Lipo
Battery: 1700~2200mAh 3S1P
Weight: 71g
Dimensions: 27.6 x 36mm
Shaft Size: 3.175mm
Recommended
for models between 600-800g
|
|
|
|
|
REVOX
G3013/18
No. Of cells : 3-4 Li-Poly
RPM/V : 910KV
Operating Current: 15A ~ 20A
Peak Current: 29A (15 secs)
Suggested prop: 11x5.5E,
12x4.7, 12x6
Lipo
Battery:2200mAh-2500mAh 3S1P
Weight: 118g
Dimensions: 32mm x 37mm
Shaft Size: 5mm
Recommended
for models between 800-1100g
|
|
|
For
Helicopter
|
REVOX
APM450XT Outrunner 3850KV
- Helicopter
(2.3mm SHAFT)
No. Of cells : 3-4x Li-Poly
RPM/V : 3850
Max. efficiency current: 8 - 10.5 A (>75%)
No load current / 10 V: 0.5 A
Current capacity: 40 A/60 s
Dimensions: 22x15 mm
Shaft diameter: 2.3 mm
Weight: 59 g
Recomended model weight 450 class Electric. Heli.
|
|
|
For
Helicopter
|
REVOX
APM450XT Outrunner 3850KV
- Helicopter
(3.17mm
SHAFT)
No. Of cells : 3-4x Li-Poly
RPM/V : 3850
Max. efficiency current: 8 - 10.5 A (>75%)
No load current / 10 V: 0.5 A
Current capacity: 40 A/60 s
Dimensions: 22x15 mm
Shaft diameter: 3.17mm
Weight: 59 g
Recomended model weight 450 class Electric. Heli.
|
|
|
|
MOUNTING
TIPS FOR G2217/16
onto SNIPER 3D / SUPER ZOOM
|
All REVOX G2 Motors comes
with Back Mounting Prop Adaptor. Some may find
them not useful but it is not often the case.
The purpose of back-mount prop adaptor is for
mounting the motor onto a model that requires
firewall mounting. They are specially useful
for Profile models such as SNIPER 3D / Hacker
Super Zoom / Airfoilz etc with Motor mounting
which is cut into the fuselage.
To mount the REVOX G2 Motor into such "Firewall"
mounting, simply mount the cross radial mount
using the counter-sunk screw first. Using the
radial cross mount, position the motor onto
the firewall and mark out the 4 holes. We recommend
using Self Tapping screw, hence by marking the
4 holes, you just need to use a 1mm drill to
engrave a pilot hole (about 1mm deep) for the
tapping screws to be inserted and tighten itself
as you screw the cross radial mount onto the
firewall.
As you may notice the original shaft placement
gets in the way as you mount the motor onto
the firewall, use a 2mm metal rod, heat the
tip of the metal rod and melt the internal foam
deep enough to make clearance for the original
shaft placement to sit through nicely onto the
firewall.
Next, mount the Back-Mount prop adaptor for
your propellers. As you may pleasantly discover,
the back-mount prop adaptor actually comes with
4 long counter-sunk screws that match perfectly
onto the prop-mount. Before you mount the propeller
as per normally you would, we suggest you power-up
the model and do a full throttle check on the
prop adaptor to ensure there's no wobbling before
you mount the prop.
***IMPORTANT***
Make sure your prop is mounted right at the
dead centre, if the motor wobbles with the prop,
there will be a high chances that your propeller
is not mounted at the dead centre where it should
be wobble-free, or your prop is off-balance.
Get a prop balancer if you need to. For APC
Props, they usually have a few hub-collars which
you can use to match the diameter of the prop
adaptor, eliminating all possible gaps that
causes the wobbling.
Have Fun!
Team Sky Hobbies Singapore |
Back
to motor main page ...
|
| |
